The Metrics Menu
================

This menu is not present in the Bitmap View, and the Metrics View only contains
"Center in Width" and "Thirds in Width".

.. _metricsmenu.Center:

.. object:: Center in Width

   In the Outline and Metrics Views this centers the current glyph (makes its
   lbearing be the same as its rbearing) within the current width.

   In the Font View the same thing is done for all selected glyphs.

   Setting this value will adjust all layers so that guides in the background
   etc. will be adjusted with the rest of the glyph.

.. _metricsmenu.Thirds:

.. object:: Thirds in Width

   This is very like Center in Width above... except that I happen to prefer
   having a bit more white space after my glyphs than before them. So this
   command makes the rbearing twice the lbearing (instead of making them be the
   same).

   Setting this value will adjust all layers so that guides in the background
   etc. will be adjusted with the rest of the glyph.

.. _metricsmenu.WindowType:

.. object:: Window Type

   In the Metrics View, the window may behave in different ways.

   .. _metricsmenu.WT-Kerning:

   .. object:: Kerning Only

      This metrics view may only be used to adjust kerning

   .. _metricsmenu.WT-Width:

   .. object:: Advance Width Only

      This metrics view may only be used to adjust the advance widths of glyphs

   .. _metricsmenu.WT-Both:

   .. object:: Both

      This metrics view will adjust either the advance width or kerning

.. _metricsmenu.Width:

.. object:: Set Width...

   .. image:: /images/setwidth.png

   The Set Width command allows you to change the width of the current glyph (in
   the outline view) or all selected glyphs (in the font view). You may either
   set the width to an absolute value, change the width by adding a constant
   value to it, or multiply it by a scale factor. Normally the width will be
   expressed in em-units, but in a bitmap only font the width will be expressed
   as pixels in the current displayed font.

.. _metricsmenu.LBearing:

.. object:: Set LBearing...

   The Set LBearing command is similar to the Set Width command above, the
   dialog is pretty much the same except that it applies to the left side
   bearing rather than to the width. Setting this value will adjust all layers
   so that guides in the background etc. will be adjusted with the rest of the
   glyph.

.. _metricsmenu.RBearing:

.. object:: Set RBearing...

   The Set RBearing command is similar to the Set Width command above, the
   dialog is pretty much the same except that it applies to the right side
   bearing rather than to the width.

.. _metricsmenu.Auto:

.. object:: Auto Width...

   This command is only available in the font view.
   :ref:`It attempts to guess reasonable values for the widths <autowidth.AutoWidth>`
   (more accurately the left and right bearings) of the specified glyphs.

.. _metricsmenu.KernByClasses:

.. object:: Kern By Classes...

   This command is only available from the font and metrics views. It provides
   the user with a :ref:`dialog <metricsview.kernclass>` to manipulate kerning
   classes.

.. _metricsmenu.Remove:

.. object:: Remove All Kern Pairs

   In the font view removes all kern pairs (and kern classes) in the font.

   In the outline glyph view removes all kern pairs where the current glyph is
   the left hand glyph.

   Not present in the Metrics or Bitmap views.

.. _metricsmenu.kernpair:

.. object:: Kern Pair Closeup...

   (Sorry about the name, I couldn't think of a better).
   :ref:`Allows <metricsview.kernpair>` you to get a look at kerning between two
   glyphs at different point-sizes and to build a
   ":ref:`Device Table <metricsview.DeviceTable>`" (which allows small
   corrections from the standard behavior at specified point sizes)

   Not present in the Bitmap view.

.. _metricsmenu.VKernByClasses:

.. object:: VKern By Classes...

   This command is only available from the font and metrics views. It provides
   the user with a :ref:`dialog <metricsview.kernclass>` to manipulate vertical
   kerning classes.

.. _metricsmenu.VKernFromHKern:

.. object:: VKern From HKern

   This command is only available from the font and metrics views. It removes
   all current vertical kerning information, then it looks through the font and
   for each pair of horizontally kerned glyphs where both have a 'vert' or
   'vrt2' feature it produces a vertical kerning pair for the vertical versions
   of those glyphs. (That is: If ``A``+``V`` are horizontally kerned by -50 and
   ``A`` => ``A.vert`` and ``V`` => ``V.vert`` then this command will produce a
   vertical kerning pair between ``A.vert`` + ``V.vert`` with a value of -50)

.. _metricsmenu.VRemove:

.. object:: Remove All VKern Pairs

   In the font view removes all vertical kern pairs (and kern classes) in the
   font.

   In the outline glyph view removes all kern pairs where the current glyph is
   the left hand glyph.

   Not present in the Metrics or Bitmap views.

.. _metricsmenu.vertical:

.. object:: Set Vertical Advance...

   If vertical metrics are enabled for the font this will be active in the font
   and outline glyph view.

   It behaves exactly like Set Width... except it works on the vertical advance
   rather than the horizontal advance (width).